-
DELTA VFD007M43B VFD-M Series Drive, DELTA Inverter VFD007M43B 0.75KW 380V three Phase Original price was: 14,000.00৳ .12,500.00৳ Current price is: 12,500.00৳ .
Series: VFD-M
HM:1 HP
KW:0.75 KW
INPUT :460 V
AMP. 3 A
Input: 3 PH
Condition Brand New
Warranty: Available2 in stock
-
DIY Starter Kit: Arduino Uno R3,Breadboard, Jumper Wires,USB Cable,9V Connector. (Made in China ) Original price was: 1,300.00৳ .700.00৳ Current price is: 700.00৳ .
The Uno R3 with Cable is a micro-controller board base on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs); 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button.
Let’s discuss each component in detail.
- ATmega328 Microcontroller– It is a single chip Microcontroller of the ATmel family. The processor code inside it is of 8-bit. It combines Memory (SRAM, EEPROM, and Flash), Analog to Digital Converter, SPI serial ports, I/O lines, registers, timer, external and internal interrupts, and oscillator.
- ICSP pin – The In-Circuit Serial Programming pin allows the user to program using the firmware of the Arduino board.
- Power LED Indicator– The ON status of LED shows the power is activated. When the power is OFF, the LED will not light up.
- Digital I/O pins– The digital pins have the value HIGH or LOW. The pins numbered from D0 to D13 are digital pins.
- TX and RX LED’s– The successful flow of data is represented by the lighting of these LED’s.
- AREF- The Analog Reference (AREF) pin is used to feed a reference voltage to the Arduino UNO board from the external power supply.
- Reset button– It is used to add a Reset button to the connection.
- USB– It allows the board to connect to the computer. It is essential for the programming of the Arduino UNO board.
- Crystal Oscillator– The Crystal oscillator has a frequency of 16MHz, which makes the Arduino UNO a powerful board.
- Voltage Regulator– The voltage regulator converts the input voltage to 5V.
- GND– Ground pins. The ground pin acts as a pin with zero voltage.
- Vin– It is the input voltage.
- Analog Pins– The pins numbered from A0 to A5 are analog pins. The function of Analog pins is to read the analog sensor used in the connection. It can also act as GPIO (General Purpose Input Output) pins.
Why is Arduino recommended over other boards for beginners?
The USB port in the Arduino board is used to connect the board to the computer using the USB cable. The cable acts as a serial port and as the power supply to interface the board. Such dual functioning makes it unique to recommend and easy to use for beginners.
What is the main difference between Arduino UNO and Arduino Nano?
The Arduino Nano has a compact size and mini USB cable than the Arduino UNO.
What is the main difference between Arduino UNO and Arduino Mega?
The Arduino UNO is a standard board recommended to beginners, while Arduino Mega is used for complex projects due to its greater memory space.
Memory
The memory structure is shown in the below image:
Out of stock
-
DOP-107BV ,Delta HMI ,Delta Electronics DOP-100 Series Original price was: 15,000.00৳ .12,500.00৳ Current price is: 12,500.00৳ .Quick Details
- Place of Origin:
-
Taiwan, China
- Brand Name:
-
DELTA ELECTRONICS
- Model Number:
-
DOP-107BV
- DESCRIPTION:
-
HMI SCREEN
- APPLICATION:
-
INDUSTRIAL AUTOMATION
- TECHNICAL SUPPORT:
-
WE OFFER COMPLETE SUPPORT
- WARRANTY:
-
YES
3 in stock
-
DOP-107EV ,Touch Screen HMI Original price was: 28,000.00৳ .21,600.00৳ Current price is: 21,600.00৳ .
1 in stock
-
DOP-110CS HMI 10.1”(1024*600) 65,536 Colors TFT, Touch screen ,Delta Original price was: 30,000.00৳ .24,000.00৳ Current price is: 24,000.00৳ .
Specifications
10.1”(1024*600) 65,536 Colors TFT
Cortex-A8 800MHz CPU
256 MB RAM
256 MB ROM
2 sets of COM ports / 1 extension COM port
USB Host
USB Client
CE / UL certified
Operation Temperature: 0℃ ~ 50℃
Storage Temperature: -20℃ ~ 60℃
Pressing times: >1,000K times
2 in stock
-
DOP-DVP Programming Cable For Delta DVP Series PLC Communication Cable , Touch Panel Original price was: 1,600.00৳ .1,000.00৳ Current price is: 1,000.00৳ .
- DOP-DVP
- Cable size : 2 METER
- Brand :Amsamation
10 in stock
-
DOP-FX DOP(B)-FX Communication cable For Delta DOP-B touch panel and for Mitsubishi FX series PLC Original price was: 2,000.00৳ .1,000.00৳ Current price is: 1,000.00৳ .
DOP-FX DOP(B)-FX Communication cable For Delta DOP-B touch panel and for Mitsubishi FX series PLC
Out of stock
-
DVP-04TC-S Delta Temperature Module Original price was: 15,500.00৳ .13,500.00৳ Current price is: 13,500.00৳ .
Brand: Delta
Model: DVP-04TC-S
Condition: New2 in stock
-
DVP-14SS211 ,DVP-SS2 Series Original price was: 12,000.00৳ .9,500.00৳ Current price is: 9,500.00৳ .
Manufacturer Series DVP-SS2 Series I/O Points 494 Output Type Digital Communication Port Built-in RS-232 & RS-485 ports Brand Delta Power 24 V DC 1 in stock
-
DVP-16ES200R,ES2 series PLC Original price was: 16,000.00৳ .13,000.00৳ Current price is: 13,000.00৳ .
odel ATO-DVP-ES2 Builit-in I/O 16 / 20 / 24 / 32 / 40 / 60 I/O points Power Supply 100 ~ 240V AC (-15% ~ +10%), 50/60Hz ±5% Connector European standard removable terminal block (Pin pitch: 5mm) Operation ATO-DVP-ES2 PLC starts to run when the power rises to 95~100V AC and stops when the power drops to 70V AC.
If the power is suddenly cut off, the PLC will continue running for 10ms.Power Supply Fuse 2A / 250V AC Power Consumption 30VA DC 24V Current Output *1 500mA Power Supply Protection DC 24V output short circuit protection Voltage Withstand 1500VAC (Primary-secondary), 1500VAC (Primary-PE), 500VAC (Secondary-PE) Insulation Resistance >5MΩ at 500VDC (between all I/O points and ground) Noise Immunity ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, Analog & Communication I/O: 1kV
RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/mGrounding The diameter of grounding wire shall not be less than that of L, N terminal of the power supply.
(When many PLCs are in use at the same time, please make sure every PLC is properly grounded.)Environment Operation: 0°C~55°C (temperature), 5~95% (humidity), pollution degree 2
Storage: -25°C~70°C (temperature), 5~95% (humidity)Approvals UL508, European community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC Vibration/Shock Immunity International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 & IEC 68-2-27 (TEST Ea) Weight See below “Selection Table” Note:
*1. It is suggested that the power output should not be supplied to HMIs.2 in stock
-
DVP-16SM11N | DELTA | I/O Extension Module DVP-16SM11N | DELTA | I/O Extension Module Original price was: 6,800.00৳ .6,100.00৳ Current price is: 6,100.00৳ .
- Manufacturer : DELTA
- Product No. : DVP-16SM11N
- Product type : I/O Extension Module
- Input type : DC Type (Sink or Source)
- Voltage/Input current : 24 V DC 5 mA
- Active level : Off – On: more than 16.5 V DC
- On – Off: less than 8 V DC
- Response time : Approx. 10ms
- Circuit isolation : By photocoupler
- Input display : LED
3 in stock
-
DVP-16SP11T Delta PLC Extension module Original price was: 7,500.00৳ .6,500.00৳ Current price is: 6,500.00৳ .
Specifications for this Product:
Attribute Value Manufacturer Delta Electronics PLC Model DVP16SP11T Product Series DVP Series I/O points 16 Digital Input 8 Digital Output 8 Voltage – Supply 100 ~ 240VAC, 24V DC Output Type Transistor DC Input H type Mounting Type Din Rail Termination Style Pluggable Screw Terminal Maximum Operating Temperature 55°C Minimum Operating Temperature 0°C 2 in stock
-
DVP04AD-S,Delta Analog Output Module Original price was: 15,000.00৳ .13,500.00৳ Current price is: 13,500.00৳ .
Delta: Analog Input Module (DVP04AD-S)
The A/D Conversion – In industrial automation, many measuring units are transmitted by analog signals. The most frequently adopted range for the signals are voltage -10 ~ 10V and current -20 ~ 20mA. To use the analog signals as the parameters for PLC operations, you have to convert them into digital values first. For example, the voltage -10 ~ 10V is first converted into values -8,000 ~ 8,000 by an A/D module, and the PLC will read/write the control registers (CR) in the AD module by FROM/TO instructions. The signals sent back to the PLC for operations will be digital K-8,000 ~ K8,000.
DVP04AD (or DVP06AD) analog signal input module receives external 4 (or 6) points of analog input signals (voltage or current) and converts them into 14-bit digital signals. The MPU can read/write the data in the module by using FROM/TO instructions in the program. There are 49 16-bit control registers in the module. You can select voltage input or current input by the wiring. Range for voltage input: ±10V (±8,000, resolution: 1.25mV). Range for current input: ±20mA (±4,000, resolution: 5μA).
2 in stock
-
DVP10SX11T Delta PLC 24VDC 2AI/2AO 4DI/2DO transistor Original price was: 20,000.00৳ .16,300.00৳ Current price is: 16,300.00৳ .
DVP10SX11T
DVP S-Series Analogue CPU
Input: 6 Sink/Source 24VDC
Output: 2 NPN Transistor
Analog In: 2 points (-20>20mA _ -10> 10V)
Analog Out: 2 points (-20>20mA _ -10> 10V)
COM: 2 RS232/RS485 portsDelta’s high-performance, high-speed DVP series PLCs are the most efficient and incorporate communication capabilities. Benefits include numerous convenient built-in controls for easy access to operations and monitoring of communication functions. The module-type unit offers huge space savings, allowing easy clip-on expansion possibilities. The high performance and large I/O units of the PLCs are a high value solution for machine control and industrial automation.
Common features
Adopts 32-bit CPU
Clip-on extension modules – general (right side)
Plug-in terminals for easy wiring and maintenance
Compact size (H) 90 mm x (D) 60 mm DIN rail mounting
Built-in high-speed counters up to 100-200 kHz (depending on model)
Dual RS232 and RS485 MODBUS ASCII / RTU compatible communication ports
Program language: instruction list (IL), ladder diagram (LD), sequential function diagram (SFC)
SX2 series digital and analogue I/OsThe slim-type SX2-series PLC offers 6/14 digital and 12-bit analogue I/O points built-in. It is extendable with the DVP-S series left- and right-side extension modules.
Key features:
No battery required
Execution speed: LD: 0.35 ?s
Supports 2-axis linear and arc interpolation
High speed counters: 2 x 100kHz and 6 x 10kHz
High speed pulse output: 2 x 100kHz and 2 x 10kHz
Program capacity: 16k steps / data log: 10k words
Supports DVP-S series left-side (high-speed) expansion modules
Supports standard MODBUS ASCII / RTU protocol and PLC connection function1 in stock
-
DVP14SS211R PLC Module (8+6) IO, Delta Electronics Original price was: 12,000.00৳ .9,500.00৳ Current price is: 9,500.00৳ .
- Brand :
- DELTA
- Product Type :
- Electronics & Accessories
- Model :
- DVP14SS211R
- Power Supply :
- 24V DC
- Number of Inputs :
- 8
- Number of Outputs :
- 6
- Output Rating :
- 1.5 A
- Origin :
- China
-
DVP16SP11R Delta PLC Expansion Module DVP-S Original price was: 7,500.00৳ .6,500.00৳ Current price is: 6,500.00৳ .
DVP16SP11R Delta Plc DVP-S expansion module
The DVP-S series of Delta PLCs offer a wide variety of hardware configurations, communication, power and computing capabilities to meet the most diverse needs in industrial automation.
Whether your automation project is large or small, the DVP-S Series PLCs are the right choice at the right price.- DVP16SP11R
- DVP S-series expansion module
- Connection: right
- Input: 8 Sink/Source 24VDC
- Output: 8 Relays
Can be used with Delta SS / SA / SE / SX / SV / MC PLCs
The Delta DVP-16SP11R series is an Input/Output expansion module for slimline industrial PLCs from Delta Electronics. The Delta DVP-16SP11R is equipped with an expansion bus that allows additional modules to be mounted on the right side without external wiring.
The DVP-16SP11R expansion module with its mixed configuration of 8 inputs and 8 outputs is the most flexible choice if you need to implement your automation project with additional sensors and actuators.Out of stock
