DVP-16ES200R,ES2 series PLC
| odel | ATO-DVP-ES2 | ||||||
| Builit-in I/O | 16 / 20 / 24 / 32 / 40 / 60 I/O points | ||||||
| Power Supply | 100 ~ 240V AC (-15% ~ +10%), 50/60Hz ±5% | ||||||
| Connector | European standard removable terminal block (Pin pitch: 5mm) | ||||||
| Operation | ATO-DVP-ES2 PLC starts to run when the power rises to 95~100V AC and stops when the power drops to 70V AC. If the power is suddenly cut off, the PLC will continue running for 10ms. |
||||||
| Power Supply Fuse | 2A / 250V AC | ||||||
| Power Consumption | 30VA | ||||||
| DC 24V Current Output *1 | 500mA | ||||||
| Power Supply Protection | DC 24V output short circuit protection | ||||||
| Voltage Withstand | 1500VAC (Primary-secondary), 1500VAC (Primary-PE), 500VAC (Secondary-PE) | ||||||
| Insulation Resistance | >5MΩ at 500VDC (between all I/O points and ground) | ||||||
| Noise Immunity | ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, Analog & Communication I/O: 1kV RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m |
||||||
| Grounding | The diameter of grounding wire shall not be less than that of L, N terminal of the power supply. (When many PLCs are in use at the same time, please make sure every PLC is properly grounded.) |
||||||
| Environment | Operation: 0°C~55°C (temperature), 5~95% (humidity), pollution degree 2 Storage: -25°C~70°C (temperature), 5~95% (humidity) |
||||||
| Approvals | UL508, European community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC | ||||||
| Vibration/Shock Immunity | International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 & IEC 68-2-27 (TEST Ea) | ||||||
| Weight | See below “Selection Table” | ||||||
| Note: *1. It is suggested that the power output should not be supplied to HMIs. |
|||||||
Original price was: 16,000.00৳ .13,000.00৳ Current price is: 13,000.00৳ .
Specifications
- MPU points:16 / 20 / 24 / 32 / 40 / 60
- Program capacity: 16k steps
- Built-in with 3 COM ports: 1 RS-232 port and 2 RS-485 ports, all are able to operate independently (Master/Slave)
- Max. I/O points: 256 input points + 16 output points, or 256 output points + 16 input points
- DVP-EX2 MPU is built in with 12-bit 4AD/2DA and offers analog/temperature modules of 14-bit resolution
- Built-in with 8 high-speed input points (2 points for 100kHz, 6 points for 10kHz) and supports U/D, U/D Dir, A/B counting modes
- New motion control instructions: Close loop control, alignment mark, shield, immediate variable speed, S-Curve acceleration/deceleration
- Application in emerging industry:Exclusive instructions and function blocks designed for PV solar tracker
- Handy instructions for frequency inverter: For controlling the forward running, reverse running, RUN and STOP of Delta’s AC motor drives
- Password protection:Password for subroutine, user ID, restriction on trial times
- Highly efficient instruction efficient instruction execution
Related Products
- Manufacturer : DELTA
- Product No. : DVP-16SM11N
- Product type : I/O Extension Module
- Input type : DC Type (Sink or Source)
- Voltage/Input current : 24 V DC 5 mA
- Active level : Off – On: more than 16.5 V DC
- On – Off: less than 8 V DC
- Response time : Approx. 10ms
- Circuit isolation : By photocoupler
- Input display : LED
3 in stock
- Brand :
- DELTA
- Product Type :
- Electronics & Accessories
- Model :
- DVP14SS211R
- Power Supply :
- 24V DC
- Number of Inputs :
- 8
- Number of Outputs :
- 6
- Output Rating :
- 1.5 A
- Origin :
- China
Analog I/O Module
● 4 points of analog input voltage (-10 V ~ +10 V) / current (-20 mA ~ +20 mA)
● 2 points of analog output voltage (0 V ~ +10 V) / current (0 mA ~ +20 mA)
● Input / output resolution: 12-bit
● Built-in RS-485 interface
● Single-ended input
Product category
PLC
sub-category
DVP Slim Series
Partner name
Delta
Series name
DVP-Slim Expansion
Attributes
PLC Module
Expansion Module
I/O Selection
Mix AI/AO
Supply
24VDC
Output Type
N.A.
In Built
1 in stock
- Manufacturer : Mitsubishi Electric
- Product No : FX3U-32MT / ES-A
- Product type : Main units with 32 I/O
- FX3U-32MT / ES-A is the third generation in their family FX Series PLC is a compact PLC and successful form of Mitsubishi Electric.
- A new special feature is the system “bus adapter” supplemented for bus systems useful for extended special features and block network communications.
- Extended special features and block network communications.
- Maximum Likelihood can expand up to 10 blocks on the new bus.
- The CPU with 32 I / O: 16 inputs and 16 outputs transistor (S)
- Power supply: 100 -240 VAC
- Power: 35 W
- Memory program: 64,000 Steps
- Integrated real-time clock: 16 (100 Khz).
- Counter: 235
- Timer: 512
- Integrated portal RS232C, RS485
- Origin: Mitsubishi – Japan
- Shipping Weight: 2 kg
1 in stock
| Type | FX3U |
|---|---|
| Power Supply (V) | 100-240 |
| Current Type | AC |
| Program Memory | 64K STEPS |
| Program Memory Unit | RAM |
| Integrated Digital Inputs | 16 |
| Integrated Digital Outputs | 16 |
| Output Type | TRANSISTOR |
| Output Logic | SINK |
| Local I/O Points | 256 |
| Local Remote I/O Points | 384 |
| Expandable | YES |
| Cycle Time LD (ns) | 65 |
| Cycle Time MOV (ns) | 642 |
| RS-422 | 1 |
| Power Consumption (W) | 35 |
| Buffer Battery | YES |
| Protection Class | IP10 |
| Min. Ambient Temperature (°C) | 0 |
| Max. Ambient Temperature (°C) | 55 |
| Series | MELSEC-F SERIES |
Made in Japan
FX2N-48MR-001 datasheetPDF datasheet
FX2N-48MR-001 PROGRAMMING MANUAL IIMITSUBISHI FX2N-48MR-001 Product information and technical parameters：
Brand: MITSUBISHI
Name: PLC
Model: FX2N-48MR-001
Max input / output points: 48 points.
Supply voltage: 100 – 240VAC.
Input points: 24 points.
Output points: 24 points.
Output type: relay.
Power consumption: 50VA.
Weight (kg):0.85.
Size (WxHxD) mm:182x90x87.
- Made in JAPAN
| Type | FX3U |
|---|---|
| Power Supply (V) | 100-240 |
| Current Type | AC |
| Program Memory | 64K STEPS |
| Program Memory Unit | RAM |
| Integrated Digital Inputs | 24 |
| Integrated Digital Outputs | 24 |
| Integrated Analogue Inputs | N/A |
| Output Type | RELAY |
| Output Logic | N/A |
| Local I/O Points | 256 |
| Local Remote I/O Points | 384 |
| Expandable | YES |
| Cycle Time LD (ns) | 65 |
| Cycle Time MOV (ns) | 642 |
| USB | OPTION |
| Ethernet Port | N/A |
| RS-232 | N/A |
| RS-422 | 1 |
| RS-485 | N/A |
| Power Consumption (W) | 40 |
| Buffer Battery | YES |
| Protection Class | IP10 |
| Min. Ambient Temperature (°C) | 0 |
| Max. Ambient Temperature (°C) | 55 |
| Series | MELSEC-F SERIES |
Product Dimensions & Weight
| Width (mm) | 182 |
|---|---|
| Height (mm) | 90 |
| Depth (mm) | 86 |
| Weight (kg) | 0,85 |
2 in stock
| SERIES | MELSEC IQ-F SERIES |
|---|---|
| TYPE | DC INPUT (SINK/SOURCE) |
| POWER SUPPLY (V) | 24 |
| CURRENT TYPE | DC |
| OCCUPIED I/O POINTS ON PLC | 16 |
| INTEGRATED DIGITAL INPUTS | 16 |
Made In JAPAN
1 in stock
| Manufacturer Series | DVP-SS2 Series |
| I/O Points | 494 |
| Output Type | Digital |
| Communication Port | Built-in RS-232 & RS-485 ports |
| Brand | Delta |
| Power | 24 V DC |
1 in stock
DELTA PLC DVP40ES200R 100-240VAC 24DI 16DO Relay Output
Extended Product Type : DVP-ES2series
Product ID: DVP40ES200R
Delta Type Designation : DVP-ES2 series
1 in stock
Delta: Analog Input Module (DVP04AD-S)
The A/D Conversion – In industrial automation, many measuring units are transmitted by analog signals. The most frequently adopted range for the signals are voltage -10 ~ 10V and current -20 ~ 20mA. To use the analog signals as the parameters for PLC operations, you have to convert them into digital values first. For example, the voltage -10 ~ 10V is first converted into values -8,000 ~ 8,000 by an A/D module, and the PLC will read/write the control registers (CR) in the AD module by FROM/TO instructions. The signals sent back to the PLC for operations will be digital K-8,000 ~ K8,000.
DVP04AD (or DVP06AD) analog signal input module receives external 4 (or 6) points of analog input signals (voltage or current) and converts them into 14-bit digital signals. The MPU can read/write the data in the module by using FROM/TO instructions in the program. There are 49 16-bit control registers in the module. You can select voltage input or current input by the wiring. Range for voltage input: ±10V (±8,000, resolution: 1.25mV). Range for current input: ±20mA (±4,000, resolution: 5μA).
2 in stock
| SERIES | MELSEC-F SERIES |
|---|---|
| TYPE | FX3U |
| INTERFACE | USB |
2 in stock
Reviews
There are no reviews yet.